lunes, 18 de septiembre de 2017

ANUNCIO DE COPIADORAS


ANUNCIO DE COPIADORAS

   QUE TAL AMIGOS COMO LES PLATIQUE LA VEZ ANTERIOR DESPUÉS DE UNOS AÑOS 8 APROXIMADAMENTE, DECIDÍ CONTRATAR EL ANUNCIO EN EL DIRECTORIO MAS PRESTIGIADO DE LA ÉPOCA, ESTOY HABLANDO DE LA "SECCIÓN AMARILLA" O "PAGINAS AMARILLAS" O "YELLOW PAGES" EN ALGUNAS OTRAS LATITUDES, QUE SI FUNCIONABA Y FUNCIONABA MUY BIEN ANTES DE LA LLEGADA DE GOOGLE, PERO BUENO EN AQUEL TIEMPO ERA LO QUE TODO MUNDO DEBÍA TENER PARA QUE LOS POTENCIALES CLIENTES TE UBICARAN, Y FUE ASÍ COMO PARA EL AÑO DE 2004 EMPECE A APARECER EN EL DIRECTORIO ZONA SUR DE LA CIUDAD DE MÉXICO BAJO EL NOMBRE COMERCIAL DE "PROTECH", DICHO NOMBRE COMERCIAL NO FUE DE MUCHO BENEFICIO YA QUE EN AQUEL TIEMPO NO SABIA QUE LAS POLÍTICAS DE ANUNCIOS IBAN CONFORME AL ABECEDARIO, ASÍ QUE LOS NOMBRES DE LOS ANUNCIANTES QUE EMPEZABAN CON LA LETRA "A" APARECÍAN EN LOS PRIMEROS LUGARES DE LA SECCIÓN CORRESPONDIENTE A COPIADORAS Y PUES COMO MI NOMBRE EMPEZABA CON LA LETRA "P" YA SE IMAGINARAN,  ESTABA HASTA LAS ULTIMAS PAGINAS DE LA SECCIÓN DE COPIADORAS EN DONDE POCA GENTE SOLIA BUSCAR (COMO OCURRE HOY EN GOOGLE) Y PUES NO HABÍA NADA QUE HACER PARA CAMBIAR DICHA SITUACIÓN , SOLO RESTABA ESPERAR AL SIGUIENTE AÑO PARA CORREGIR DICHO ERROR DE INEXPERTO EN ESOS MENESTERES.

   YA CON LA EDICIÓN IMPRESA EN CIRCULACIÓN ESPERE TENER MAS SOLICITUDES ES DE SERVICIO DE NUEVOS CLIENTES MAS SIN EMBARGO CON EL PASAR DE LOS MESES ME DI CUENTA QUE NO IBA A FUNCIONAR COMO ESPERABA Y NI MODO A SEGUIR REPARTIENDO TARJETAS DE PRESENTACIÓN EN TODOS LOS LUGARES DONDE HUBIERA OPORTUNIDAD Y FUE ASÍ COMO TRASCURRIÓ ESE AÑO EN EL CUAL SOLO 4 NUEVOS CLIENTES ADQUIRÍ GRACIAS AL ANUNCIO PUBLICITARIO, Y ESTA BIEN, YA QUE APRENDES A NO COMETER EL MISMO ERROR LA PRÓXIMA VEZ , EN EL TRABAJO DE CUALQUIER MANERA APRENDÍ MAS DE LAS OTRAS MARCAS Y SUS FALLAS REPETITIVAS O CONSTANTES, COMO SON LAS RAYAS BLANCAS, DEBIDO A FILAMENTOS YA MUY DETERIORADOS O ATORAMIENTO DE HOJAS, POR QUE LAS GOMAS DE ALIMENTACIÓN DE PAPEL YA ESTABAN DEMASIADO LISAS Y YA NO ALIMENTABAN EL PAPEL A TIEMPO, O LA DE RODILLOS DE CALOR CON EL TEFLON TAN DETERIORADO QUE YA NO PARECÍA COPIADORA SINO MAQUINA DE OFFSET SE ACUERDAN, EN DONDE LA IMAGEN DE LA COPIA SE REPETÍA AL FINAL DE LA COPIA, O COMO LAS COPIAS MANCHADAS Y QUE SOLO LIMPIABAS ESPEJOS Y SE CORREGÍA LA FALLA, ESO POR LO REGULAR APLICABA A TODAS LAS MARCAS Y MODELOS DE COPIADORAS DE AQUEL ENTONCES PERO TAMBIÉN CADA MARCA TENIA SUS FALLAS PARTICULARES COMO EN LAS XEROX 1025 RECUERDO QUE COMO DABAN LATA LOS CLUTCHS DE REGISTRO O EN LAS XEROX 1012 SERIE MARATÓN, EL TREN DE ENGRANES ERA LO MAS COMÚN DE DAÑARSE EN ESOS EQUIPOS, ESTOY HABLANDO DE MAQUINAS COPIADORAS ANÁLOGAS YA QUE EN AQUELLOS ENTONCES SE GESTABA EN LOS LABORATORIOS LAS COPIADORAS DIGITALES, PERO EN EL CAMPO SOLO HABÍA MAQUINAS ANÁLOGAS Y LAS MAQUINAS CANON TAMBIÉN TENÍAN SUS FALLAS TÍPICAS COMO LOS ATORAMIENTOS DE HOJAS POR CAUSA DE UÑAS DE SALIDA SUPERIORES DEL RODILLO FUSOR O CUANDO NO SACABA BUENA CALIDAD DE COPIA SOLO LIMPIABAS LA PLACA DE REFERENCIA BLANCA Y LISTO COMO POR ARTE DE MAGIA LAS FALLAS DE CALIDAD DE COPIASE CORREGÍAN, ASÍ MISMO SI AJUSTABAS MAL LA ALTURA DE LOS FILAMENTOS DE CARGA LA COPIA SIEMPRE SALIA DISPAREJA, O COMO EN LAS CANON DE ALTO VOLUMEN SI NO AJUSTABAS CORRECTAMENTE LA ALTURA DE LOS FILAMENTOS DE CARGA SE ARQUEABA EL VOLTAJE Y TERMINABA CON EL CILINDRO PICADO , NO SE SI ALGUIEN SE ACUERDE DE ESO Y TAMBIÉN SI LA MALLA DE CARGA ESTABA YA MUY GASTADA HACIA LA MISMA FALLA, Y OTRO PUNTO A RECORDAR ES AQUEL DE LOS MODOS DE SERVICIO DE AQUELLAS MAQUINAS Y SUS AJUSTES TAMBIÉN TÍPICOS COMO SON LA LUZ , LA CARGA, EL VOLTAJE DE BÌAS, ETC. ESTA INFORMACIÓN QUE CELOSAMENTE ATESORABAN LAS COMPAÑÍAS DE LAS DIFERENTES MARCAS, SOLÍA SER UN TANTO CUANTO DIFÍCIL DE OBTENER, PERO GRACIAS A MI BUEN AMIGO MARCELO CRISTOBAL , QUE COMO MENCIONE ANTES , YA TENIA ALGÚN TIEMPO DESEMPEÑÁNDOSE POR SU CUENTA, DICHA INFORMACIÓN ESTABA DISPONIBLE YA QUE EL COMPRABA UNOS MANUALES DIGAMOS "GENÉRICOS" PERO QUE TRAÍAN LA INFORMACIÓN PRECISA PARA VARIAS MARCAS Y MODELOS DE COPIADORAS EL NOMBRE DE DICHOS MANUALES "GENÉRICOS " ERA: TRAVIAS; ALGUIEN LOS LLEGO A CONSULTAR? , SI ES ASI SABRÁS DE LO QUE HABLO, Y CON ESO YA ESTABAS DEL OTRO LADO YA QUE ESTA INFORMACIÓN ES MUY NECESARIA EN EL CAMPO Y NOS SACABA DE APUROS EN MUCHOS MOMENTOS, YA QUE COMO DIJE TRAÍA INFORMACIÓN PRECISA ACERCA DE COMO ENTRAR EN LOS MODOS DE SERVICIO Y LOS COMANDOS O DIRECCIONES PARA AJUSTAR COSA ESPECIFICAS E INCLUSO CADA CIERTO TIEMPO SALÍAN NUEVAS EDICIONES YA SABEN CADA QUE SE HACIA RENOVACIÓN DE ALGUNA SERIE DE ALGUNA MARCA.

   PASO EL AÑO Y EL CONTRATO DEL ANUNCIO EXPIRO , MAS SIN EMBARGO ME RECOMENDARON EL DIRECTORIO GENERAL CIUDAD DE MÉXICO POR OTRO AÑO PERO ESTA VEZ YA MAS INFORMADO Y HABIENDO APRENDIDO DE EL ANUNCIO ANTERIOR LO CONTRATE PERO YA CON EL NOMBRE ACTUAL DE ALFA COPIADORAS E INCLUÍ EL ESLOGAN " EL INICIO DE UN BUEN SERVICIO"  Y DE AHÍ EN ADELANTE LA HISTORIA DIO UN VUELCO, DE LO CUAL LES PLATICARE EN OTRO BLOGG.

   POR LO PRONTO ES TODO Y ESPERO TUS COMENTARIOS O VISITA MI PAGINA







jueves, 14 de septiembre de 2017

tecnico de copiadoras independiente

Técnico de copiadoras independiente


   QUE TAL AMIGOS, ESPERO QUE SE ENCUENTREN BIEN Y POR MI PARTE QUIERO PEDIR DISCULPAS A TODOS LOS QUE HAN HECHO EL FAVOR DE LEER ESTE BLOGG YA QUE ESTUVE UNOS AÑOS AUSENTE Y  TAL VEZ MUCHOS DE USTEDES QUEDARON CON GANAS DE LEER MAS ACERCA DE LA HISTORIA CONTADA Y BUENO AQUÍ CONTINUA DICHA HISTORIA.  MUCHAS GRACIAS.
   Cuando la relación laboral para la empresa en la que trabajaba se termino, como a mediados del 1995, y tras cinco años de aprendizaje y experiencia, me encontré desempleado y teniendo en mente conseguir otro empleo mejor, obviamente, pero por motivo de la crisis económica acaecida un año antes (1994), las empresas en ese momento ofrecían sueldos mas bajos de lo que percibía hasta ese momento en la empresa recién dejada, así que, decidí no buscar mas y empezar a ofrecer mis servicios de forma independiente, lo cual no fue fácil ya que para esos entonces ya existían técnicos independientes que daban servicio, mas sin embargo para la marca Canon había muy pocos técnicos independientes, la mayoría reparaba marcas mas comerciales en ese momento como xerox y algunas otras, pero de la marca Canon había muy pocos y bueno eso fue lo que me ayudo en un principio ya que en el transcurso de unos meses, me di cuenta que  debía diversificarme en marcas ya que, al reparar una sola marca no hay muchos reportes que atender, así que me fui a ver a mi amigo Marcelo Cristobal, el cual ya tenia algún tiempo siendo independiente y fue ahí con el como empece a conocer el sistema de los equipos de copiado Xerox y algunas otras marcas como sharp, que en algunos modelos eran muy similares a xerox, y por supuesto todos los equipos de copiado eran análogos y solo sacaban copias, y así fue como ya mas informado, y adquirido cierta experiencia en estas marcas, empece a tener mas reportes de servicio que atender diariamente y claro que andaba todo el día en la ciudad de México y su zona metropolitana reparando equipos como el xerox 3100, o xerox 1025, recuerdo que también reparaba algunos equipos de marcas muy poco conocidas como la triumph-adler, alguno de ustedes las recuerda?, maquinas copiadoras muy buenas en su tiempo o como aquella sharp que se abría como concha y que en este momento no recuerdo el modelo, de platina móvil, recuerdan?, y por supuesto todas las canon análogas que conocía como la np 1010/1020 aunque empece a trabajar con la Np 270, Np2015 y Np4540, se acuerdan de ellas ? cuando trabaje en Canon, pero en aquellos momentos ya estaban los modelo como la NP 1015/1515; NP2020/2120; NP 3825, NP4050, o las de alto volumen como la NP 6150 o la NP 6060 , esta ultima en particular fallaba constantemente; y así andaba de un lado a otro atendiendo algunos servicios propios y otros de mi buen amigo ya que el tenia mayormente población de equipos xerox , así que me ayudaba para aprender mas de ellas y sobre la marcha allegarme mas clientela pasando a las papelerías, escuelas, centros de copiado u oficinas que encontraba en el camino a presentarme y dejarles una tarjeta con todos mis datos para que me llamaran si fuera necesario y así brindarles el servicio de reparación de sus equipos de copiado, y para esos momentos ya había echo los tramites necesarios ante hacienda para poder expedir facturas ya que muchos clientes las requerían para sus obligaciones fiscales, y aun así el trabajo mismo t va recomendando y con o sin factura realizaba el servicio sin ningún contratiempo.
   Con el correr del tiempo, aun con los años de experiencia y el conocimiento adquirido te das cuenta que las grandes compañías siempre se llevan la mayor parte del servicio y esta bien ya que sus expectativas como empresas de prestigio siempre estas puestas en lo mas alto y aun así siempre les seras como un pequeño tropiezo en el camino, ya que durante la crisis vivida en aquellos años los independientes ganamos terreno , ya que la gente no podía pagar los altos costos del mantenimiento de dichas compañías y buscaba opciones en el directorio que durante mucho tiempo fue el rey de la publicidad, antes de la llegada de la era digital y google por supuesto, y estoy hablando de la tristemente celebre "sección amarilla"  y quien no tenia publicidad ahí era como estar en "underground" para la gente que busca servicios no existías si no estabas ahí, y como dije anteriormente aun asi el trabajo que hagas solo te recomienda y así fue durante unos años hasta que entendí que había que invertir en la publicidad de el directorio, ya que las metas y ambiciones que suele uno tener son altas también y pues no había mas que hacer. mas que invertir y fue así como contrate un espacio pequeño en dicho directorio y a manera de prueba -por recomendación- el directorio donde me anuncie fue el zona sur de la ciudad de México.

   Motivo de el siguiente blog sera contarte la experiencia vivida ya con un anuncio el el directorio mas importante de aquella epoca, por el momento es todo y espero que me dejen algun comentario ya saben bueno o malo siempre sera bienvenido y visiten mi pagina .

martes, 13 de junio de 2017

Venta de copiadoras

   

Venta de copiadoras 



En este mundo de las copiadoras multifuncionales, últimamente han surgido muchas compañías que venden equipos de copiado, las cuales solo venden el equipo sin el soporte técnico adecuado. Nosotros tenemos copiadoras baratas con servicio incluido, así como también copiadoras económicas para papelerías y también con servicio técnico incluido, o si lo que buscas es comprar una copiadora de alto volumen, tenemos planes de financiamiento, así que siempre encontrarás copiadoras económicas y sin que tengas la preocupación por el soporte técnico ya que también te lo incluimos.
Vendemos copiadoras de la marca mas económica y rentable del momento, la marca Ricoh, tenemos de todos los tamaños y modelos, así como también de otras marcas como son: canon, sharp, xerox, hp, samsung, etc. 


Por lo tanto, si andas buscando comprar una copiadora multi funcional, ya no busque mas, aquí con nosotros la encontrará.



copiadoras ricoh
copiadoras ricoh








Equipo multifuncional ricoh modelo ECP 5210/5220 de 52 paginas por minuto, copia, imprime y escana directo a USB o SD, conexion USB y red ethernet, copiado duplex automatico, alimentador de originales y touch screen a color.


LLEVATELO POR TAN SOLO 12 MIL PESOS .
EQUIPO SEMI NUEVO CON TRES MESES DE GARANTÍA


EN EL VIDEO SE MUESTRA EL FUNCIONAMIENTO DEL EQUIPO ANTES DESCRITO Y LA RAPIDEZ DEL FLUJO DEL TRABAJO.






Equipo multifuncional marca ricoh modelo MPC 300, de 30 p.p.m. a color
copia, imprime y escane, conectividad USB y red, amplia y reduce, tamaño carta oficio.







Llama ahora 55 51 59 02 48 y te resolvemos cualquier duda que tengas para que adquieras el equipo que mejor se adapte a tus necesidades de copiado e impresión, o si prefieres enviarnos un correo a alfacopiadoras@gmail.com, te enviamos toda la informacion prtinente o visita nuestro sitio web:









lunes, 7 de noviembre de 2016

VENTA DE COPIADORAS


www.alfacopiadoras.infored.mx
COPIADORAS

Venta de copiadoras usadas, de medio uso y reacondicionadas


Aquí encontraras copiadoras de alta calidad de las mejores marcas y en excelentes condiciones de operación a un excelente precio.

Cuando necesitas comprar una copiadora, impresora o multifuncional nuevo, generalmente piensas en que tan caro te puede costar, en comparación con uno seminuevo o usado, y que te sea útil. 
No se el tipo de negocio que tengas pero a veces es mas difícil de lo que parece decidir que equipo de fotocopiado o impresión adquirir y que sea adecuado para tu negocio.
En Alfa copiadoras te asesoramos para que adquieras un equipo de fotocopiado o impresión mas optimo y con todas las funciones necesarias para que le saques el máximo provecho a tu inversión

Todas las copiadoras, impresoras y multifuncionales que vendemos son de ultima generación y de las mejores marcas como son: CANON, RICOH, SHARP, HP, SAMSUNG, BROTHER; por mencionar las mas conocidas, y obviamente de una gran variedad de capacidades y precios, en alto , mediano y bajo volumen de impresión mensual, ademas de contar con todos los consumibles y refacciones de las maquinas fotocopiadoras o de impresión que vendemos.

venta de copiadoras
oferta desde 4 mil pesos 
venta de copiadoras
oferta desde 14 mil pesos

venta de copiadoras
oferta desde 3,500 pesos
venta de copiadoras
oferta desde 20 mil pesos 

ENTREGA INMEDIATA 

Copiadoras, impresoras y multifuncionales en venta:


*copiadoras a color
*copiadoras B&N
*copiadoras formato tabloide
*impresoras WI FI
*copiadoras con y sin conectividad
*copiadoras usadas
entrega inmediata


Cuando quieres comprar una copiadora nueva o usada normalmente estas preguntas te asaltan la cabeza:

Si compro una copiadora, ¿Viene con una garantía total?
La mayoría de los fabricantes tienen una garantía de 12 meses en la venta copiadoras nuevas y nosotros tres meses en copiadoras usadas y copiadoras semi nuevas
¿Viene con un contrato de servicio / mantenimiento?
No este se adquiere por separado  una vez terminada la garantía en copiadoras nuevas y  usadas es un contrato de servicio que por lo general tiene una duración de 12 meses.
Hay financiamiento disponible para una copiadora en venta?
Sí, hay una variedad de opciones de financiamiento disponibles, y el financiamiento de una copiadora es relativamente simple.
¿Hay arrendamiento / alquiler de las opciones de compra?
Sí, hay contrato de arrendamiento para adquirir opciones disponibles, pero no son muy comunes y suelen costar mucho más que la compra de una copiadora desde el principio.
Solicita una cotización de una copiadora en  venta en este momento,
 Nuestros asesores de copiadoras pueden responder a sus preguntas 






viernes, 5 de diciembre de 2014

CÓDIGOS DE ERROR EN COPIADORA RICOH MP 2510


www.alfacopiadoras.infored.mx

 ERRORES DE COPIADORA RICOH MP 2510

EN ESTA OCASIÓN TE DEJO LOS CÓDIGOS DE LAS FALLAS Y SU DESCRIPCIÓN SOLO QUE EN INGLES ASÍ QUE DEBES TENER NOCIÓN DE EL IDIOMA PARA ENTENDER ESTE MATERIAL DE CUALQUIER MANERA CON LAS HERRAMIENTAS DE HOY EN DÍA ES FÁCIL TRADUCIR AL CASTELLANO O AL IDIOMA QUE GUSTES ASÍ QUE ESPERO SEAN DE UTILIDAD A LA COMUNIDAD CABE DESTACAR QUE ESTE MATERIAL LO BAJE DE LA RED DESPUÉS DE UNA BÚSQUEDA EXHAUSTIVA.
EN CUALQUIER CÓDIGO DE ERROR ES NECESARIO QUE LLAMES AL SERVICIO TÉCNICO PARA QUE DESBLOQUEE EL EQUIPO Y LE REVISE LA POSIBLE CAUSA DEL ERROR, SALVO ALGUNAS EXCEPCIONES EN LAS QUE EL EQUIPO SE DESBLOQUEA APAGANDOLO Y PRENDIENDOLO NUEVAMENTE O ENTRANDO A MODO SE SERVICIO LO CUAL EN MUCHOS CASOS EL OPERADOR DE LA MAQUINA SABE EL PROCEDIMIENTO PARA TAL EFECTO, Y SI NO SABES COMO HACERLO SERA NECESARIO LLAMAR AL SERVICIO TÉCNICO 
Code
Description
Causes
101
Exposure lamp error 1
The standard white level was not detected properly when scanning the white plate.
• Exposure lamp defective • Lamp stabilizer defective • Exposure lamp connector defective • Standard white plate dirty • Scanner mirror or scanner lens out of position or dirty • SBU defective
102
Exposure lamp error 2
The exposure lamp was on longer than the allowed time (3 min.) after scanning of the originals was completed.
• SBCU defective • IPU defective • Controller board defective
120
Scanner home position error 1
The scanner home position sensor does not detect the on condition during initialization or copying.
• Scanner motor defective • Scanner motor drive board defective • Scanner HP sensor defective • Harness between SBCU and HP sensor loose, disconnected, damaged • Harness between SBCU and scanner motor loose, disconnected, damaged • SBCU defective • Scanner wire, timing belt, pulley, or carriage defective
121
Scanner home position error 2
The scanner home position sensor does not detect the off condition during initialization.
• Scanner motor defective • Scanner motor drive board defective • Scanner HP sensor defective • Harness between SBCU and HP sensor loose, disconnected, damaged • Harness between SBCU and scanner motor loose, disconnected, damaged • SBCU defective • Scanner wire, timing belt, pulley, or carriage defective
122
Scanner HP Sensor - Error 1
The HP sensor remains on while the carriage is returning to the home position.
• Scanner motor defective • Scanner motor drive board defective • Scanner HP sensor defective • Harness between SBCU and HP sensor loose, disconnected, damaged • Harness between SBCU and scanner motor loose, disconnected, damaged • SBCU defective • Scanner wire, timing belt, pulley, or carriage defective
123
Scanner HP sensor - Error 2
The HP sensor does not switch on after the carriage has returned to the home position.
• Scanner motor defective • Scanner motor drive board defective • Scanner HP sensor defective • Harness between SBCU and HP sensor loose, disconnected, damaged • Harness between SBCU and scanner motor loose, disconnected, damaged • SBCU defective • Scanner wire, timing belt, pulley, or carriage defective
141
Black offset correction error
Black offset could not be corrected after SP4800 was done.
• Lens block defective • SBCU defective
143
SBU auto adjust error
The machine could not acquire the white or black peak level setting at power on, or after SP4428 (SBU Auto Adjust) was done.
• Exposure lamp disconnected • There is no blank sheet of A3 size paper on the platen • White plate dirty or missing
144
SBU connection error
The IPU does not detect the SBU connection signal.
Harness between SBU and IPU board loose, disconnected, or damaged.
165
Copy Data Security Unit error
An error occurred when the machine attempted to recognize the Copy Data Security Unit board.
• The Copy Data Security Unit board is not installed • The Copy Data Security Unit board is installed, but it is not the correct type for the machine.
193
Image transfer error
The IPU board does not finish within 1 minute after the image data has been transferred to the controller board.
• IPU board defective • Controller board defective • Video controller defective
195
DFGATE assert error
The DFGATE signal does not assert within 30 seconds after the original has been scanned.
• ADF interface cable loose, disconnected, or damaged • SBCU defective • Mismatched firmware between the SBCU board and ADF
196
DFGATE negate error
The DFGATE signal does not negate within 1 minute after the DFGATE has been asserted.
• ADF interface cable defective • SBCU defective • Mismatched firmware between the SBCU board and ADF
197
DFGATE error
The DFGEATE signal has already been asserted at the original scan.
• ADF interface cable defective • SBCU board defective • Mismatched firmware between the SBCU board and ADF
198
Memory address error
The IPU board does not receive the memory address from the controller board.
• Mismatched firmware between the SBCU board and controller board • Controller defective • SBCU defective • IPU board defective Note: Before you replace a board, update the firmware. This can repair the error.

199
DF scanning finish error
The original does not finish scanning with in 1 minute
• ADF interface cable defective • SBCU board defective • Mismatched firmware between the SBCU board and ADF
302
Charge roller error
A charge roller current leak signal is detected.
• Charge high voltage supply board defective • Connection at PCU loose, disconnected, or damaged
320
Polygon motor error
• The XSCRDY signal did not activate (go LOW) within 10 sec. after the polygon motor turned on. • The XSCRDY signal did not deactivate (go HIGH) within 3 sec. after the polygon motor turned off. • The polygon motor continued to rotate for the prescribed number of rotations for 200 ms after the XSCRDY signal went HIGH (deactivated). • After the polygon motor turned on, or after the machine detected that the prescribed number of rotations had changed, the XSCRDY signal did not go LOW (active).
• Polygon motor I/F harness loose, disconnected, or defective • Polygon motor defective • Polygon motor driver defective • SBCU board defective
322
Laser synchronization error
The main scan synchronization detector board cannot detect the laser synchronization signal for more than 10 consecutive 50 ms intervals.
• Poor connection between the laser synchronization detector board and the SBCU board • Laser synchronization detector board out of position • Laser synchronization detector board defective • SBCU board defective • LD unit defective
323
LD drive current over
• The LD drive current exceeded 100 mA. • The XLDERR of the LD board was detected LOW twice within 100 ms. • Initialization of the PMACA failed.
• LD unit defective (not enough power, due to aging) • Poor connection between the LD unit and the SBCU board • SBCU board defective
350
ID sensor calibration - Error 1
One of the following conditions occurred when the ID sensor pattern was calibrated during printing: • Vsp > 2.5V • Vsg < 2.5V • Vsp = 0V • Vsg = 0V
• ID sensor defective or dirty • ID sensor harness disconnected or connector is damaged • SBCU defective • Scanning system or image creation system malfunction • High voltage power supply board (power pack) defective
351
ID sensor calibration - Error 2
The following conditions occurred simultaneously when the ID sensor pattern was calibrated during printing: • Vsg = 5V • PWM = 0 (LED current drop)
• ID sensor dirty or defective • ID sensor harness disconnected, or connector damaged • SBCU board defective • High voltage power supply board (power pack) defective
352
ID sensor calibration - Error 3
During printing the 2.5V value for edge detection of the ID sensor pattern could not be detected after 800 ms.
• ID sensor dirty or defective • ID sensor harness disconnected, or connector damaged • SBCU defective • High voltage power supply board (power pack) defective
353
ID sensor adjustment Error 1
Error occurred during automatic adjustment of Vsg: • Vsg output did not attain 4V, even with PWM = 255 (maximum current for LED) • Vsg output was greater than 4V, even with PWM=0 (no current for the LED)
• ID sensor dirty or defective • ID sensor harness disconnected, or connector damaged • SBCU defective • High voltage power supply board (power pack) defective • Scanning system or image creation system malfunction
354
ID Sensor Adjustment Error 2
Error occurred during automatic adjustment of Vsg. Vsg could not be adjusted to 4.0V±0.2V within 50 ms even after 20 attempts.
• ID sensor dirty or defective • ID sensor harness disconnected, or connector damaged • SBCU defective • High voltage power supply board (power pack) defective • Scanning system or image creation system malfunction
355
ID sensor error
For details about the cause of the problem, please refer to SC350~354 above
• ID sensor dirty or defective • ID sensor harness disconnected, or connector damaged • SBCU board defective • High voltage power supply board (power pack) defective • Scanning system or image creation system malfunction
389
TD sensor error
TD sensor output was less than 0.5V, or more than 0.5V 10 times in succession. If the fax unit is installed, this SC is issued immediately. If the fax unit is not installed, this SC is issued after the prescribed number of copies has printed.
• TD sensor defective • TD sensor connector damaged.
390
TD sensor error
The TD sensor outputs less than 0.5V or more than 4.0V 10 times consecutively during copying. Note: • If the fax option is installed, this SC is issued immediately. • If the fax option is not installed, this SC is issued after the prescribed number of pages is copied.
• TD sensor abnormal • Poor connection of the PCU
391
Development bias leak
A development bias leak signal is detected.
• Poor connection at the PCU bias terminal • High voltage supply board defective
392
TD sensor initial setting error
Initialization of the new PCU unit failed. TD sensor output voltage fell out of the adjustment range (2.0 +- 0.2 V.
• The PCU toner seal was not removed • ID sensor defective • TD sensor defective • Drum does not turn • Development roller does not turn

398
PCU error South Korea only
Illegal PCU unit.
Install the correct type of PCU.
399
Illegal toner bottle South Korea only
The toner bottle installed is not intended for use with this machine.
Install the correct type of toner bottle.
401
Transfer roller leak error 1
A transfer roller current leak signal is detected. The current feedback signal for the transfer roller is not detected within the correct time.
• High voltage supply board set incorrectly or defective • Transfer roller set incorrectly or damaged • Transfer unit set incorrectly
402
Transfer roller leak error 2
A transfer roller current leak signal is detected. The current feedback signal for the transfer roller is not detected within the correct time.
• Transfer roller set incorrectly or damaged • High voltage supply board set incorrectly or defective
411
Separation bias leak error
A separation bias leak signal is detected.
• High voltage supply board defective • Discharge plate defective
490
Toner supply motor leak error
More than 1 ampere supplied to the toner supply motor for longer than 200 ms.
• Toner supply motor defective
500
Main motor lock
A main motor lock signal is not detected for more than 500 ms after the main motor starts to rotate, or the lock signal is not detected for more than 500 ms during rotation after the last signal.
• Too much load on the drive mechanism • Main motor defective
501
1st paper tray lift motor malfunction
The paper lift sensor is not activated after the tray lift motor has been on for 18 seconds.
• Paper lift sensor connection loose, disconnected, or damaged • Paper lift sensor defective • Tray lift motor connection loose, disconnected, or damaged • Tray lift motor defective • Obstruction that causes overload on the drive mechanism
502
2nd paper tray lift motor malfunction
The paper lift sensor is not activated after the tray lift motor has been on for 18 seconds.
• Paper lift sensor connection loose, disconnected, or damaged • Paper lift sensor defective • Tray lift motor connection loose, disconnected, or damaged • Tray lift motor defective • Obstruction that causes overload on the drive mechanism
503
3rd paper tray lift motor malfunction (optional paper tray unit)
The paper lift sensor is not activated after the tray lift motor has been on for 18 seconds.
• Paper lift sensor connection loose, disconnected, or damaged • Paper lift sensor defective • Tray lift motor connection loose, disconnected, or damaged • Tray lift motor defective • Obstruction that causes overload on the drive mechanism
504
4th paper tray lift motor malfunction (optional paper tray unit)
The paper lift sensor is not activated after the tray lift motor has been on for 18 seconds.
• Paper lift sensor connection loose, disconnected, or damaged • Paper lift sensor defective • Tray lift motor connection loose, disconnected, or damaged • Tray lift motor defective • Obstruction that causes overload on the drive mechanism
506
Paper tray motor lock (optional paper tray unit)
A motor lock signal is not detected for more than 1.5 s or the lock signal is not detected for more than 1.0 s during rotation.
• Paper tray motor connection loose, disconnected, or damaged • Paper tray motor defective • Obstruction that causes overload on the drive mechanism
508
LCT rear fence drive error
The return position sensor is not activated after the rear fence drive motor has been on to lower the tandem tray for 8 seconds.
• Rear fence motor connection loose, disconnected, or damaged • Rear fence motor defective • Return position sensor connector loose, disconnected, or damaged • Return position sensor defective • Obstruction that causes overload on the drive mechanism
509
LCT side fence drive error
The side fence positioning sensor is not activated for more 3 seconds when the paper stack in the left tray is moved to the right tray. The side fence close sensor is not activated for more 3 seconds after moving the paper stack to the right tray.
• Obstruction that causes overload on the drive mechanism • Side fence motor disconnected or defective • Side fence position sensor disconnected or defective• Side fence close sensor disconnected or defective
510
LCT lower limit error
The lower limit sensor does not activate within 8 seconds after the tray has been lowered.
• Tray lift motor defective • Poor connection of the tray lift motor • Lower limit sensor disconnected or defective • Obstruction that causes overload on the drive mechanism.

Code
Description
Causes
520
Paper tray error
An error occurs (i.e motor error, or sensor error, etc) for any paper tray.
• A defective motor • A defective sensor • Obstruction that causes overload on the drive mechanism
541
Fusing thermistor open
The fusing temperature did not increase 12 °C at the center or ends of the hot roller within 2 seconds after two checks from the time the fusing lamps turned on.
• Fusing thermistor out of its position because of incorrect installation • Fusing thermistor disconnected or defective • Power supply not within rated range (15% or more below rating)
542
Fusing temperature warm-up error
The fusing temperature does not reach the standby temperature within 20 seconds after the main switch is turned on.
• Fusing thermistor defective or out of position • Fusing lamp disconnected • Fusing thermostat open
543
Fusing overheat error 1
A fusing temperature over 230°C is detected for 5 second by the fusing thermistor.
• TRIAC short on PSU (PSU defective) • SBCU board defective • Fusing thermistor defective
544
Fusing overheat error 2
• A fusing temperature over 250°C is detected by the fusing temperature monitor circuit in the SBCU board. • The power was interrupted for more than 0.3 sec.
• TRIAC short on PSU (PSU defective) • SBCU board defective • Fusing thermistor defective • Voltage of power supply unstable
545
Fusing overheat error 3
After warmup, the hot roller attained full operating temperature and maintained this temperature for 10 sec. without the hot roller rotating.
• Hot roller thermistor is out of its position because of incorrect installation
546
Unstable fusing temperature
The fusing temperature varies 50°C or more twice in succession within 1 sec.
• Thermistor disconnected or defective • Fusing unit drawer installed incorrectly
547
Zero cross signal detection error
Zero cross signals are not detected within a certain period.
• PSU defective • SBCU board defective
548
Fusing unit set error
The machine does not detect the fusing unit.
• Poor connection of the fusing unit • The fusing unit is not installed
557
Zero cross waveform signal error
The waveform of the zero cross signal was detected out of range.
• Electrical noise on the power supply line
590
Exhaust fan motor error
The CPU detects an exhaust fan lock signal for more than 3.5 seconds.
• Poor connection of the exhaust fan motor • Too much load on the motor drive
611
Communication break error between SBCU and ADF
The SBCU received a break (LOW) signal from the ADF main board.
• Serial line connecting SBCU and ADF unstable • Connectors between SBCU and ADF loose, disconnected, or damaged
612
Communication command error between SBCU and ADF
The SBCU sends a command to the ADF main board that it cannot execute.
• Update the firmware • SBCU board defective
620
Communication timeout between SBCU and finisher: Error 1
The SBCU cannot receive a response within 100 ms after 3 attempts after sending data to the finisher.
• Serial line connecting SBCU and finisher unstable • External noise
621
Communication timeout between SBCU and finisher: Error 2
A break (LOW) signal was received from the finisher.
• Serial line connecting SBCU and finisher unstable • External noise

650
Communication timeout error between SBCU and duplex unit
The SBCU cannot receive a response within 1 sec. from the duplex unit.
• Serial line connecting SBCU and duplex unit unstable • External noise • SBCU board and duplex main board connection defective or loose • Duplex main board defective • SBCU board defective
669
EEPROM Communication Error
The machine failed to detect a match between the read/write data for the EEPROM on the SBCU after 3 attempts.
• EEPROM installed incorrectly • EEPROM defective After you check the installation, turn the machine off and on. If this does not repair the problem, replace the SBCU.
670
Engine response error
After powering on the machine, a response is not received from the engine within 30 seconds.
• SBCU installed incorrectly • SBCU defective • Controller board defective
672
Controller-to-operation panel communication error at startup
After powering on the machine, the communication circuit between the controller and the operation panel is not opened, or communication with controller is interrupted after a normal startup.
• Controller stall • Controller board installed incorrectly • Controller board defective • Operation panel connector loose or defective
720
Finisher motor error
The meaning of this SC error depends on which finisher is installed. 500-sheet Finisher B442 There is a problem with the upper transport motor.1000-sheet Finisher B408 There is a problem with the registration motor.
• The motor connectors are loose, disconnected or damaged. • The motor is defective
721
Lower transport motor error - 1000sheet Finisher B408
There is a problem with the lower transport motor.
• The motor connectors are loose, disconnected or damaged. • The motor is defective
722
Finisher jogger motor error - 1000-sheet Finisher B408
The finisher jogger H.P sensor remains de-activated for a certain time when returning to home position. The finisher jogger H.P sensor remains activated for a certain time when moving away from home position.
• Jogger H.P sensor disconnected or defective • Jogger motor connectors loose, disconnected, or damaged • Jogger motor defective
724
Finisher staple hammer motor error - 1000-sheet Finisher B408
Stapling does not finish within 600 ms after the staple hammer motor turned on.
• Staple jam • Stapler overload caused by trying to staple too many sheets • Staple hammer motor defective
725
Finisher stack feed-out motor error - 1000-sheet Finisher B408
The stack feed-out belt H.P sensor does not activate within a certain time after the stack feed-out motor turned on.
• Stack feed-out H.P sensor defective • Stack feed-out motor defective
726
Finisher lift motor error
The stack height sensor does not activate within a certain time after the shift tray lift motor turned on. Note: This error applies to the 500-sheet and the 1000-sheet finisher.
• Shift tray lift motor defective • Stack height sensor defective
727
Finisher staple hammer motor error - 500-sheet Finisher B442
Stapling does not finish within a certain time after staple hammer motor turned on.
• Staple jam • Stapler overload caused by trying to staple too many sheets • Staple hammer motor defective
728
Finisher exit motor/paper stack height error
The meaning of this SC error depends on which finisher is installed. 1000-sheet Finisher B408 Exit motor error. 500-sheet Finisher B442 Stack height sensor error. The stack height detection lever does not return to its home position before going to detect the stack height.
Exit motor error (B408) • Exit motor connector loose, disconnected, or damaged • Exit motor defective Stack height sensor error (B442) • Stack height lever solenoid defective • Stack height sensor defective • Lever sensor defective • Main control board defective
730
Finisher stapler motor error - 1000-sheet Finisher B408
The stapler does not return to its home position within a certain time after the stapler motor turned on. -or-The stapler H.P sensor does not activate within a certain time after the stapler motor turned on.
• Stapler motor defective • Stapler H.P sensor defective • Poor stapler motor connection
731
Finisher motor error
The meaning of this SC error depends on which finisher is installed. 1000-sheet Finisher B408 Exit guide plate motor error. The exit guide plate open sensor or exit guide plate HP sensor does not activate within a certain time after the exit guide plate motor turned on. (1000-sheet finisher) 500-sheet Finisher B442 Output tray motor error. The tray upper limit sensor does not activate within a certain time after the shift motor turned on. (500-sheet finisher)
1000-sheet Finisher • Exit guide plate motor defective • Exit guide plate HP sensor defective • Exit guide plate open sensor defective 500-sheet Finisher • Output tray motor defective • Tray upper limit sensor defective
732
Finisher shift motor error - 1000-sheet Finisher B408
Roller shift does not finish within a certain time after the shift motor turned on.
• Shift motor defective • Shift tray HP sensor defective

770
Shift tray shift motor error
During a shift operation the sensor state did not change (off to on, or on to off) within 2.4 sec.
• Shift sensor defective • Shift motor defective
791
Bridge communication error
The machine cannot communicate with the finisher with the bridge unit installed.
• Poor connection between the finisher and mainframe • Harness damaged or defective
792
Finisher connection error
The machine cannot communicate with the finisher with the bridge unit installed.
• Finisher connection defective
793
Interchange communication error
The machine cannot communicate with the interchange unit properly when the duplex unit is installed.
• Interchange unit installed incorrectly • Interchange unit connection loose, disconnected, or damaged • Interchange unit harness damaged
800
Startup without video output end error (K)
Video transfer to the engine is started, but the engine did not issue a video transmission end command within the specified time.
• Controller board defective
804
Startup without video input end (K)
A video transmission was requested from the scanner, but the scanner did not issue a video transmission end command within the specified time.
• Controller board defective
818
Watchdog error
While the system program is running, no other programs can run (due to a bus hold or endless loop).
• Defective controller board
819
Kernel abnormal end error
A HDD error or a software error has occurred, terminating the SCS process, gwinit process, and finally the kernel program. A system process has exhausted the RAM.
• HDD error • Software application error • RAM shortage • MBU jumper set incorrectly. For more, see "Fax Option Type B766" manual "1. Installation".
820
Self-Diagnostic Error: CPU
An unexpected exception or interruption has occurred.
• Defective controller board • Software defective • MBUjumper set incorrectly. For more, see "Fax Option Type B766" manual "1. Installation".
821
Self-Diagnostic Error: ASIC
The ASIC returned an error during the self-diagnostic test because the ASIC and CPU timer interrupts were compared and determined to be out of range.
• Controller board defective
822
Self-Diagnostic Error: HDD
The hard disk drive returned an error during the self-diagnostic test.
• HDD defective • HDD connector defective • Controller board defective
823
Self-diagnostic Error: NIC
The network interface board returned an error during the self-diagnostic test.
• Controller board defective
824
Self-diagnostic Error: Resident NVRAM
The resident non-volatile RAM returned an error during the self-diagnostic test.
• Replace the resident NVRAM on the controller board • Replace the controller board
826
Self-diagnostic Error: NVRAM/Optional NVRAM
The NVRAM or optional NVRAM returned an error during the self-diagnostic test.
• Replace the NVRAM on the controller board
827
Self-diagnostic Error: RAM
The resident RAM returned a verify error during the self-diagnostic test.
• Update the controller firmware again • Replace the 256 MB memory

828
Self-diagnostic Error: ROM
The resident read-only memory returned an error during the self-diagnostic test.
• Controller board defective • Update the controller firmware
829
Self-diagnostic Error: Optional RAM
The optional RAM returned an error during the self-diagnostic test.
• Replace the optional memory. • Controller board defective
838
Self-diagnostic Error: Clock Generator
A verify error occurred when setting data was read from the clock generator via the I2C bus.
• Replace the controller board
840
EEPROM error 1
During input/output with the EEPROM on the controller board, one of the following errors occurred: • A read error occurred and continued after 3 retries. • A write error occurred.
• EEPROM defective; replace the controller board • EEPROM has reached the end of its service life
841
EEPROM error 2
The values read from the three areas during the mirroring check phase did not match. The data is being written into the three areas differently.
• EEPROM on the control board defective, or has reached the end of its service life. Replace the controller board.
850
Network I/F Abnormal
NIB interface error.
• Controller board defective (NIB function built into the controller board. Replace the controller board.
851
IEEE 1394 I/F Abnormal
IEEE1394 interface error. Note: This SC code applies to the B205/B209. The D007/D008 does not support IEEE 1394.
• IEEE1394 interface board defective • Controller board defective
853
Wireless LAN board error 1
At startup the wireless LAN board could be accessed, but the wireless LAN board (IEEE 802.11b or Bluetooth) could not access the controller board.
• Wireless LAN board not installed when the machine was turned on
854
Wireless LAN board error 2
The board that holds the wireless LAN board can be accessed, but the wireless LAN board (802.11b/Bluetooth) itself cannot be accessed while the machine is operating
• Wireless LAN board has been removed during machine operation.
855
Wireless LAN board error 3
An error was detected for the wireless LAN board (802.11b or Bluetooth).
• Wireless LAN board defective • Wireless board connection not tight
856
Wireless LAN board error
An error is detected for the wireless LAN board (802.11b or Bluetooth).
• Wireless LAN board defective • PCI connector loose
857
USB I/F Error
The USB driver is unstable and generated an error. The USB I/F cannot be used. The USB driver can generate three types of errors: RX, CRC, and STALL errors. Only the STALL error can generate this SC code.
• USB 2.0 disconnected • Controller board defective
860
Startup without HD connection at main power on
The hard disk connection is not detected.
• Cable between HDC and HDD loose or defective • HDD power connector loose or defective • HDD defective • Replace the controller board
861
HDD error 1
The HDD was not detected when the machine was turned on. The hard disk connection is not detected.
• Cable between HDC and HDD loose or defective • HDD power connector loose or defective • HDD defective • Replace the controller board
862
HDD error 2
Maximum number of bad sectors detected on HD. Up to 101 bad sectors have appeared in the area on the hard disk where image data is archived, and the hard disk may require replacement.
• Format the HDD with SP5832. Note: If you continue to use an HDD with bad sectors, this can have an effect on performance. Replace the HDD as soon as possible.

863
HDD error 3
Startup without HD data lead. Data stored on the hard disk is not read correctly.
• A bad sector occurred during operation of the HDD
864
HDD error 4
HD data CRC error. During operation of the HD, the HD responded with a CRC error.
• Data transfer was abnormal in the data read from the HDD.
865
HDD access error
HDD responded to an error during operation for a condition other than those for SC863 or 864
• HDD defective.
866
SD card error 1: Recognition error
The SD card in the slot contains illegal program data.
• Use only SD cards that contain the correct data.
867
SD card error 2: SD card removed
The SD card in the boot slot when the machine was turned on was removed while the machine power was on.
• Insert the SD card, then turn the machine off and on.
868
SD card error 3: SD card access
An error occurred while an SD card was used.
• SD card not inserted correctly • SD card defective • Controller board defective Note: If you want to try to reformat the SD card, use SD Formatter Ver 1.1.
870
Address Book Data Error
Address book data stored on the hard disk was detected as abnormal when it was accessed from either the operation panel or the network.
• Software defective • HDD defective
872
HDD mail RX data abnormal
An error was detected at power on. The data received during mail receive could be neither read nor written.
• HDD sector corrupted. Reformat with SP5832 007. • If this does not repair the problem, replace the HDD.
873
HDD mail TX data error
An error was detected on the HDD immediately after the machine was turned on, or power was turned off while the machine used the HDD.
• Do SP5832-007 (Format HDD – Mail TX Data) to initialize the HDD. • Replace the HDD
874
Delete All error 1: HDD
A data error was detected for the HDD/NVRAM after the Delete All option was used. Note: The source of this error is the Data Overwrite Security Unit B660 running from an SD card.
• Turn the main switch off/on, and try the operation again. • Install the Data Overwrite Security Unit again. For more, see section “1. Installation”. • HDD defective
875
Delete All error 2: Data area
An error occurred while the machine deleted data from the HDD. Note: The source of this error is the Data Overwrite Security Unit B660 running from an SD card.
• Turn the main switch off/on, and try the operation again.
876
Log data abnormal
An error was detected in the handling of the log data at power on or during machine operation. This can be caused if you turn the machine off while it is operating.
• Software error. Update the firmware • NVRAM defective • HDD defective
880
File format converter error
A request for access to the File Format Converter (MLB) was not answered within the specified time.
• File format converter disconnected • File format converter board defective
900
Electrical total counter error
The total count contains something that is not a number.
• NVRAM incorrect type • NVRAM defective • NVRAM data scrambled • Unexpected error from external source
901
Electronic total counter error
The value of the total counter has already exceeded 9999999
• Replace the NVRAM on the controller board

920
Printer Error 1
An internal application error was detected and operation cannot continue.
• Software defective • Insufficient memory
921
Printer error 2
When the application started, the necessary font was not on the SD card.
• Font not on the SD card
925
Network File Error
The file that manages NetFile is corrupted and operation cannot continue.
• Software defective • Files on the HDD corrupted
951
F-GATE error at write request
After the IPU receives an F-gate signal, it receives another F-gate signal.
• Update the controller firmware • SBCU board defective
953
Scanner setting error
The IPU does not respond with the scanner setting signal required to start scanning processing.
• Update the controller firmware
954
Printer setting error
The IPU does not respond with the settings that are required to start image processing by the printer.
• Replace the IPU board • Replace the controller board • Update the controller firmware
955
Memory setting error
The IPU does not respond with the settings that are required to start image processing using the memory.
• Replace the IPU board • Replace the controller board • Update the controller firmware
964
Printer ready error
The printer ready signal is not generated within 17 seconds after the IPU received the print start signal.
• Replace the IPU board • Replace the controller board • Download the controller firmware
984
Print image data transfer error
The image transfer from the controller to the engine via the PCI bus does not end within 15 s after starting.
• Controller board defective • SBCU board defective • Connectors between SBCU and controller loose or defective
986
Software write parameter setting error
An unstable area at the storage destination in the settings table is set at NULL for the parameter received by the write module.
• Update the controller firmware
990
Software performance error
The software attempted to perform an unexpected operation.
• Software defective • Internal parameter incorrect • Insufficient working memory • When this SC occurs, the file name, address, and data will be stored in NVRAM. This information can be checked by using SP7-403. Note the above data and the situation in which this SC occurs. Then report the data and conditions to your technical control center.
991
Software continuity error
The software attempted to perform an unexpected operation. However, unlike SC990, the object of the error is continuity of the software.
• No operation required. This SC code does not appear on the panel, and is only logged.
992
Unexpected Software Error
Software encountered an unexpected operation not defined under any SC code.
• Software defective • An error undetectable by any other SC code occurred
995
Machine Type Information Error
After the machine power is turned on, a mismatch is detected between the CPM information sent from the controller to the engine.
• Replace the controller board with the correct board.
997
Application function selection error
The application selected by a key press on operation panel does not start or ends abnormally.
• Update the firmware for the application that failed • An option required by the application (RAM, DIMM, board) is not installed
998
Application start error
After power on, the application does not start within 60 s. (All applications neither start nor end normally.)
• Download controller firmware • Replace the controller board • An option required by the application (RAM, DIMM, board) is not installed

EN CUALQUIERA DE LOS CASOS ANTERIORMENTE DESCRITOS DE LAS FALLAS Y POSIBLES CAUSAS SI NO TIENES EL CONOCIMIENTO PARA INTERVENIR EL EQUIPO NO LO HAGAS ES MEJOR QUE LO HAGA PERSONAL CALIFICADO PARA QUE NO SE DAÑE MAS LA MAQUINA Y ASÍ EVITAR GASTOS INNECESARIOS.

PARA CUALQUIER DUDA O SOPORTE TÉCNICO CON GUSTO TE ATIENDO  SOLO TIENES QUE USAR LAS VÍAS DE COMUNICACIÓN YA CONOCIDAS, POR TU ATENCIÓN GRACIAS.


www.alfacopiadoras.infored.mx

ANUNCIO DE COPIADORAS

ANUNCIO DE COPIADORAS    QUE TAL AMIGOS COMO LES PLATIQUE LA VEZ ANTERIOR DESPUÉS DE UNOS AÑOS 8 APROXIMADAMENTE, DECIDÍ CONTRATAR EL ANU...